УЦ Микротест - источник ваших знаний
 
Личный кабинет Вход / Регистрация
 
 
 
  Вход Регистрация
Логин*
E-mail, указанный при регистрации
Пароль* не помню
 
Войти как пользователь
Вы можете войти на сайт, если вы зарегистрированы на одном из этих сервисов:
Используйте вашу учетную запись Google для входа на сайт.
 
 
0 позиций

+7 (495) 231-23-51 Москва

+7 (964) 778-99-27 Москва

+7 (343) 286-17-86 Екатеринбург

+7 (3452) 68-88-99 Тюмень

Учебный Центр «Микротест» - обучение и сертификация IT-специалистов

Курс Cisco Optical Technology Advanced (Код: N_COTA_HC)

Cisco

 


The Cisco Optical Technology Intermediate (COTI) Release 10.1 is a 3-day instructor-led course that introduces the learners to the skills that are necessary to deploy a Cisco Optical Networking System (ONS) 15454 Multiservice Transport Platform (MSTP) network from installation to protection.
The main task that learners learn during this course is how to perform node turn-up. The course covers three shelf types: the M12, M6, and M2.
Learners also learn to deploy linear and ring dense wavelength-division multiplexing (DWDM) topologies. The course covers multiplexer- demultiplexer cards, Erbium-doped fiber amplifier cards, Raman amplifiers, transponder cards, and the newest Cisco Any Rate muxponder and crossponder cards. These cards are used in terminal, amplifier, and reconfigurable optical add-drop multiplexer (ROADM) node configurations.
Learners configure wavelength selective switch (WSS) linear and single-module ROADM (SMR) rings. This course covers 10-gigabit unprotected circuits and 10-gigabit protection using Y-cable, optical channel transport unit-2 (OTU-2), and protection switch module (PSM) cards.

Курс длится 24 академических часа


Необходимая подготовка

Цели курса

  • Successfully run the Cisco CTP tool and design sample DWDM networks

  • Describe the principles of a wavelength cross-connect (WXC)-based mesh network

  • Configure a four-node WXC-based mesh network and create DWDM circuits

  • Describe the principles of a single-module ROADM (SMR)-based mesh network

  • Configure a six-node SMR-based mesh network and create DWDM circuits

  • Configure the 10 Gb data cards with appropriate G.709 options and create data circuits

  • Install and configure the Any Rate Crossponder card for 8 x 20 protected data mode

  • Properly configure Ethernet options for Layer 1 transport using the Gigabit Ethernet and 10 Gigabit Ethernet crossponder cards

  • Install Ethernet options for Layer 2 protected and unprotected data ring circuits using the Gigabit Ethernet and 10 Gigabit Ethernet crossponder cards

  • Provision incoming class of service (CoS) marking by port and by customer VLAN and incoming traffic shaping

  • Understand general queuing theory and set up quality of service (QoS) as implemented in the Gigabit Ethernet and 10 Gigabit Ethernet enhanced crossponder cards

  • Install and connect circuits to carry T1 over Ethernet

  • Install and configure 100 Gigabit Ethernet transponder and muxponder cards and circuits

  • Install the 10G Encryption Card and verify error-free operation

  • Add a node to the existing six node 40-channel ring

  • Troubleshooting techniques and lab

Подробная программа курса

Содержание

  • Cisco Transport Planner (CTP) Design Tool

  • Lab: Start the Cisco Transport Planner Software and Create a DWDM Network

  • Cisco Transport Controller (CTC) Operations

  • Lab: Configure Cisco Transport Controller and Display Network

  • WSS- and WXC-Based Mesh Networks

  • Node Turn-Up: 40/80 WXC Mesh Technology

  • Lab: Establish 4-Node 40- and 80-Channel Mesh Networks

  • Lab: Create Circuits and View Power Levels in 40 and 80 WXC Networks

  • Install Circuits and View Power Levels in WSS and WXC Networks

  • SMR-Based Network and Node Turn-Up

  • Lab: Establish Six-Node SMR1 and SMR2 Mesh Networks

  • Install Circuits and View Power Levels in SMR1 and 2 Networks

  • Lab: Create Circuits and View Power Levels in SMR1 and 2 Networks

  • G.709 Encapsulation and 10G Transponders and Encapsulation Options

  • 10 Gigabit Transponders

  • Lab: Establish 10G Transponder Circuits

  • Generic Framing Protocol G.7041 and 10G Data Multiplexer Enhanced Cards and Encapsulation Options

  • Any-Rate Muxponder and Crossponder Cards

  • Lab: Any-Rate Muxponder and Crossponder Options 8:2 Configuration

  • Ethernet and VLANs

  • 10 GE-XP and GE-XP Enhanced Cards, Settings, and Circuits Layer 1

  • Lab: 1G and 10G Crossponder Layer 1 Network

  • Lab: 1G and 10G Enhanced CrossPonder Layer Two-Ring Configuration

  • Quality of Service

  • Layer 2 XP-E Cards Protected Ring, CoS Marking by Port, Customer VLAN, and QoS

  • T1 over Ethernet and Ethernet over T1 in Crossponder Network

  • Lab: Circuits to Carry T1 over Ethernet

  • 100G Transponder and Muxponder Installation and Circuits

  • Lab: 100 Gigabit Transponders and 10 x 10 Muxponders

  • 10G Encryption Card

  • Lab: 10G Encryption Card Circuit

  • Add-a-Node Design and Installation

  • Lab: Add-a-Node to Six-Node Mesh Network

  • ONS 15454 MSTP Troubleshooting

  • Lab: MSTP Troubleshooting

Скрыть подробную программу курса

Заказать обучение «Cisco Optical Technology Advanced (N_COTA_HC)» можно, кликнув на удобную дату его проведения, по почте training AT training-microtest DOT ru или по одному из телефонов, указанных в разделе Контакты.


* 1 у.е. = 1 доллару США в рублях по курсу ЦБ РФ +3% на день выставления счета
* 1 у.е. = 1 Евро в рублях по курсу ЦБ РФ +3% на день выставления счета

 
Заказать